Pure Water Systems

Pure water setup, filtration, and flow needs for drone cleaning and waterfed pole work.

Request a Setup Review

Clean water is part of the finish

Water quality controls spotting, rinse performance, and client satisfaction. Drone cleaning, waterfed poles, and traditional exterior cleaning all need the right filtration conversation. DI and RO/DI planning is not a side detail. Source water quality, TDS, flow rate, resin life, tank capacity, and rinse expectations all affect production and finish quality.

Fit. Match the method to the job. DI filtration decisions start with source water, TDS target, resin cost, expected gallons, and how critical a spot-free finish is to the job.

System. Think in complete systems. The water system should include water checks, resin planning, flow control, hose strategy, and a process for diagnosing spotting.

Next step. Use the right buying path. Understand water quality first, then choose DI or RO/DI equipment that fits the volume and source water.

Not ready to talk yet? Start with the free playbook.

Water quality decides whether glass and solar work finish clean

TDS. Check source water before promising spotless results. High dissolved solids can exhaust resin quickly and create spotting if filtration is undersized or poorly maintained.

RO/DI vs DI. Choose filtration around volume and source water. DI-only setups may work in some conditions, while higher-volume or higher-TDS work often needs RO/DI planning for better resin economy.

Flow. Filtration must keep up with the job. The drone, waterfed poles, and rinse plan need enough clean water at working speed, not just clean water in theory.

Most water problems show up as finish problems

When the result is poor, inspect the whole water path before blaming the drone or operator.

Spotting. Check TDS, resin, rinse volume, and surface heat. Hot glass, dirty frames, high TDS, insufficient rinse, and contaminated brushes can all create poor finish quality.

Low production. Check pump, hose, elevation, filters, and reels. Flow restrictions can come from fittings, long hose runs, clogged filters, undersized pumps, or poor reel layout.

Short resin life. Check source water and pre-filtration. Bad source water or high-volume work can burn through DI resin if RO planning or pre-filtration is missing.

DI water is a quality system, not just a filter

Spot-free work depends on source water, resin condition, flow rate, rinse volume, surface heat, previous contamination, and whether the crew tests at the right time.

Check. Measure source water and output water before the job. TDS readings should guide resin use and customer expectations.

Plan. Match DI, RO, or RO/DI to source water and volume. High TDS or large jobs can burn through resin fast if production is not planned.

Avoid. Do not trust old resin, unknown source water, or hot glass blindly. Spotting complaints usually come from skipped water checks or wrong assumptions.

When spots appear, diagnose before blaming the method

Minerals, hydrophobic glass, soap residue, poor rinse, heat, dirty frames, and contaminated brushes can all leave marks.

Check water. Retest output at the brush or delivery point. A good reading at the tank does not prove the final rinse is clean.

Check surface. Look for oxidation, sealant, hard-water history, or construction debris. Some marks are not solved by pure water alone.

Check process. Rinse volume, dwell, brush cleanliness, and edge detail. Small process errors show up quickly on glass and solar panels.

Choose DI or RO/DI from water facts, not habit

The right filtration setup depends on source TDS, gallons per job, required finish, travel pattern, refill access, and whether the same water feeds drone, waterfed, solar, or glass work.

DI-only fit. Lower volume or lower TDS situations where resin use is manageable. Watch: resin cost, output TDS, job size, glass heat, rinse volume, and how often the operator can check and replace media.

RO/DI fit. Higher volume, higher TDS, or recurring commercial work. Watch: production rate, tank storage, waste water handling, pump support, membrane care, and whether the system keeps up with the crew.

Hybrid water fit. Mixed routes where drone and waterfed tools share the same clean-water supply. Watch: simultaneous demand, hose layout, final rinse point, meter placement, and who is responsible for water checks during the job.

Next step

Build water quality into the system plan. Filtration is not an accessory when the finish depends on it. Plan it before choosing tank size, pump flow, hose length, or route pricing.

← Back to the library